I’ve been working hard trying to get my yard prettier. Last week I painted my brown and tan resin pots — yellow. And I love the change that made in our yard.

With all of the new pots and cushion covers, it really made my old, faded porch swing stick out. So I thought I would try recovering it.

You know those projects that SEEM like they will be really easy to do?? This was one of those. I didn’t really think it out very well. And it almost became a “craft fail” quite a few times.

But I pushed through and I am SO glad that I did!!

Here’s what I did (and some mistakes to avoid in case you want to try this sometime). Plus, this would be a fun thing to look for in yard sales this summer. You should be able to pick an old swing up very inexpensively.

Here’s what I did: 

The first tip I can give you is — think this project out. 

I thought I could get rid of the old cover and make a new one with ties that tied to the frame, but once I got that made, I discovered it wasn’t going to work. So I had to start all over again. 

What I discovered is that the material that was used in the original cover is made to be VERY strong. It’s criss-crossed the way that duct tape is and that makes it able to bear the weight of several people sitting on the swing. Another thing that I discovered is that the way this swing was constructed, there is very little support in the frame, most of the support comes from the cover fitting EXACTLY to the frame and attached through ingenious straps on the back.

So I went back to the drawing board. I decided to use the old cover, but to make a NEW quilted cover that fits over the old one. That way I still use the strong original cover that fits perfectly with the extra strong material. But it also looks pretty with the new, quilted cover.

For the material, I used OUTDOOR TABLECLOTHS from Target. I wanted to use outdoor fabric and I thought using outdoor fabric tablecloths would cut down on the cost of the project. Plus, I loved the bright colors of the tablecloths.

I used three tablecloths for this project. Two for the cushion – the front and the back, and another for the canopy. But if you want to cut down on the cost, you can use a different piece of material for the underside of the cushion instead of a tablecloth.

So what I did was I laid out one tablecloth and then laid the old cushion on top of the tablecloth as a pattern — I cut the tablecloth to the same size, but added 1 inch around each side for the seam allowance and to leave room for the batting inside.

For the front side of the cushion, I cut the sides the same size as the first, then I added 8 inches to the top and bottom sides of the cushion cover. I did this because I wanted to make a flap on the top and bottom of the cushion cover so that it would fold over the top and bottom of the cushion and hold the cover onto the underlying cushion.

Once those two pieces of fabric were cut out, I folded and sewed all of the edges of the fabric under so there were no unfinished edges.

Then I pinned the cut-out tablecloth pieces together, with the right-sides inside.

And I sewed each side of the cushion cover and flipped the fabric right-side out.

The next thing I did was I inserted the 3-layers of batting inside of the cushion cover and sewed the top and bottom seams shut, holding in the batting.

Remember – the top and bottom flaps of the cushion cover are still open.

I wanted to keep the batting from getting all bunched up inside the cushion, so I quilted the cover with my machine — with straight lines across the cushion to attach the batting to the cushion cover.

Then I folded the open top and bottom fabric onto the back of the top and bottom of the cushion and sewed it down at the edges, creating a pocket at each end.

Then I put the NEW cover on top of the old, existing cover and tucked the top and bottom of the swing into the pockets, to hold the cover in place.

I also decided to make it even more secure by making a tie out of scraps of the fabric to attach to each of the bars that hold the swing seat onto the frame. I sewed those ties onto the back of the new cushion.

The Top: 

I decided to use the existing top too. The fabric tablecloth was a little see-through and I wanted it to be shadier. So I took the canopy top and laid it on top of another tablecloth.

I cut the material out to the same size as the old canopy top, with an additional inch around the whole cover. Each of the edges of the canopy top are notched, so I did the same thing with the fabric.  I folded the edges under so there were no exposed seams.

The original top also had scalloped edges, I decided to make the top square, so I didn’t cut those out.

The canopy top is held onto the top frame with sleeves that are sewn onto the underside of the top. I reinforced those with the same fabric as the new cover.

I pinned the new fabric onto the old cover. I cut off the scalloped edges of the original top and then I sewed around the whole outside of the old top, attaching it onto the new one. I folded the old material under, so there were no exposed seams.

Then I attached the canopy to the canopy frame.

I really love my new little “old” swing. It really updates the swing and adds so much to the yard. This is my favorite place to eat lunch in the summer!

I still need to make a screen for the air conditioning unit that is right around the corner. Maybe I will tackle that project next week!!

What projects are YOU working on at your house? 
Let me know in the comments – I would love to hear YOUR ideas!!

Have a Happy Day! 

xox

PS — It’s Friday! 

My favorite day of the week. 

Why?? It’s the time when I can see YOUR great ideas!

I hope you can stop by for the Weekend Wrap Up Party!

I love to feature YOU!

The party starts tonight at 6 pm MST.

The post Outdoor Swing Makeover! appeared first on Tatertots and Jello.